Highlighting VAZ 2107 with his own hands

In order that would give the car dashboard VAZ 2107, a bright and beautiful, we decided to make the blue lights of the dashboard. What would make a beautiful lighting was done by the LED board to be installed in place of a standard backlight, so that would be all rose beautifully and accurately is necessary to modify the scale of the instrument panel. That would combine the instrument scale can be set in white LEDs, which have good brightness and replace the standard bulbs. Installing a blue backlight for the dashboard requires 6 LEDs and 6 resistors, which will have a resistance of not less than 850 ohms and 5 white LEDs of high brightness. All LEDs must be installed first in the cartridge, and then in the dash. The second step will be removing panels and visor, do not forget to remember the position of the hands of devices. Using a thin knife to gently peel the standard box from the LED, and then gently wipe off the green filter. Will look bad and white lights, but to achieve a beautiful sports atmosphere will make the blue. You will have to very carefully and neatly glued blue film with tweezers. Cut out all the necessary parts of the film and rovnenko decompose, it is easy to stick to the adhesive paste. After fixing the film is better to check the glow and if you are satisfied proceed to the assembly. Do not forget for the arrows, they should not be displaced. Do highlight dl SAUO. Standard LED should be replaced by tekstolitnuyu panel with blue LED, and red patches to install red LEDs. What would be the light blue and red LEDs strongly blended can set the partition between the sectors. In order that would make uniform illumination attach to the base lid foil. This will help make the glow of the dashboard more smooth and bright. This blue light will help make the dashboard of the car VAZ 2107, a rich and beautiful at night, which would give the car greater reliability. Standard instrumentation and lighting VAZ 2107 looks quite plain and dull, at night to look at it quite pleasant. Lighting, made their own hands will cause you a sense of dignity to yourself and your car. Before proceeding with the work necessary to prepare everything carefully and think out a plan of action, in which case your work will be faster and better. Get a quality LED, checking them carefully before using, buy a blue film, good glue, as well as prepare the tools that you may need to install your lighting. You will need a thin stationery knife, tweezers, and preferably two, and possibly a drill with a drill. Prepare all necessary materials and tools you can start working on installing a blue LED light on your vases 2107.

Car repairs with their own hands

The modern car - mechanically complex device, stuffed with various electronics, and at first glance, to be thrust under the hood with a wrench himself - hopeless task. However, not all so sad. There are a number of works that are able to run any car owner who can distinguish the spanners from carob and understanding in what direction to unscrew the nut. All the car break down can be divided into two main groups - failures caused due to problems with electronic filling your car and damage associated with mechanical malfunction of components and assemblies. In the first case without the services of a qualified person can not do - repair of automotive electronics is simply impossible without computer troubleshooting. But in the latter case, much can be done independently. If a fault occurs in the first place you need to determine which of the units of the automobile is out of order. Then, after an accurate diagnosis, there are two ways to repair - give the car for a hundred or remove the faulty unit and give yourself a repair is not the whole machine, namely, the faulty node that will be significantly cheaper. What is the benefit? After all, for the work of removing and posleremontnoy install any unit in the workshop with you take the money, and often the cost of mounting and dismounting, such as CPR will be comparable to the cost of repair of the CAT! Why pay money for something that you are able to do and independently? In order to remove the broken node from the car, you'll need the room (garage, shed) from the observation well, a set of tools and a little patience. Very harmless for this to get a good technical description of your car (you can download and in the internet). Now let's go step by step: 1. Before removing the unit is not too lazy to carefully examine the upcoming scope of work, identify all the locking compound. Note the number and placement of threaded connections on your machine and in the manual may be small differences! 2. Unplug all members of the shooting site electrical connectors, hoses and cables. It should be done slowly, carefully remembering that where joined, pads for connector is colored tape mark or special colored markers to the assembly not confuse that to join. 3. Before you unscrew the unit to drain fluid from his technical (from PPC - oil, from the steering rack dekstron it.d.) 4. Unscrewing the retaining assembly bolts and nuts, do not be lazy neatly folded out of prefabricated containers, not throwing bolts in the garage! It often happens that the fastening bolt replaced if lost analog is not easy, but in case of repair of vehicles produced in the United States simply can not (the Americans are not metric and inch thread) 5. Filmed unit should be cleaned from oil, soot and dirt - perhaps you yourself will be able, after a careful examination to understand the cause and fix it without any problems. 6. If the problem on its own did not work, you need to decide where to sit in the repair of a broken node. Typically, specialized repair shops, say, starter / generator is enough in any city and you need to choose a phone shop, ready to undertake repairs on the conditions it would suit you. 7.

Painting a car body with their hands

Over time, even the best quality paint cars lose their color quality: fade, crack, slazit, deteriorated by corrosion. That makes car owners to address the issue of painting his car. With self-painting cars need to be prepared for the fact that about 90 percent of the entire process will have on the preliminary work, and only 10 percent on the very painting and further drying of the body parts. Before painting the car need to be washed thoroughly - on a clean surface is much easier to see defects in paintwork. Careful examination of the entire vehicle will determine the order that requires a car body paint or a complete enough to implement a local painting. Recommended prior to painting to inspect the bottom, legs and other body parts - if in the near future will need to repair, then painting is better to wait. Convinced of the need to paint the car, you can start preparing the body for this process. It is desirable to paint the body, and then it dried, in parts - separate doors, fenders, hood, what they should be removed. Previously with the body of the car removed all the items that will hinder the implementation of the painting. These elements include gaskets, moldings, locks, and decorative inserts. If we were to paint without removing such elements, the places that paint does not need to be borne by the stencil, paper, cardboard and attached them with masking tape. Protection of such parts from the paint can also serve as petroleum jelly or a special paste (a mixture of glycerin, dextrin, chalk and water). Place a body with flaws in the paint and rust are opened and completely cleaned of rust, then covered with primer. Old paint from the surface of the body is removed by mechanical or chemical means. Mechanical method is the simplest but most time-consuming - peeled off the surface with brushes, skins, scrapers. Not all places at the same time manage to clean off. When chemical method prepares a special solution in which the wetted body parts and paint coming off. After removing the paint, the entire surface of the body a second time cleared of traces of rust and corrosion (mechanical or chemical means) and degreased with white spirit. Quality degreasing should be very high, since not treated field is new in some time lag behind the surface. If necessary, the surface of the body is aligned with putty, but its use is desirable to reduce to a minimum. Zashpatlevannye place after drying, are aligned, degreased and processed by the primer. After doing all these works can proceed to paint. It is best to make a special spray paint. Painted body surface should be done in several stages. The first phase - a verification, in which a thin layer of paint to identify flaws and quality control zashpatlevannyh parts of the body. After eliminating defects through 20 minutes after the first stage, we can apply the main coat. Drying painted parts of the body in any case can not be produced in the sun - it is in the garage or anywhere else indoors for 2-3 days. Perhaps, after painting and drying on the surface of the body will be visible before unnoticed flaws.